Aviation Maintenance Terms beginning with N
N1
A symbol representing the rotational speed of the low- pressure compressor in a dual-spool gas turbine engine.
N2
A symbol representing the rotational speed of the high- pressure compressor in a dual-spool gas turbine engine.
Nacelle
An enclosed compartment, normally in the leading edge of the wing, in which an aircraft engine is mounted.
Nailing strip
A method of applying pressure to the glue in a scarf joint repair in a plywood skin. A strip of thin plywood is nailed over the glued scarf joint with the nails extending into a supporting structure beneath the skin. The strip is installed over vinyl sheeting to prevent it sticking to the skin. When the glue is thoroughly dry, the nailing strip is broken away and the nails removed.
Nap of the fabric
The ends of the fibers in a fabric. The first coat of dope on cotton or linen fabric raises the nap, and the fiber ends stick up. These ends must be carefully removed by sanding to get a smooth finish.
Naphtha
A volatile, flammable liquid distilled from petroleum. It is used as a cleaning agent and solvent, and is present in some blended turbine-engine fuels.
Naphtha
A volatile and flammable hydrocarbon liquid used chiefly as a solvent or as a cleaning fluid.
Naturally aspirated engine
A reciprocating engine that depends upon atmospheric pressure to force the air/fuel mixture into the cylinders. Naturally aspirated engines are neither supercharged nor turbocharged.
Nautical Mile (NM)
A unit of length used in the fields of air and marine navigation. In this document, a nautical mile is always the international nautical mile of 1852 m exactly.
Navigation Accuracy Category for Position (NACP)
Used to indicate, with 95 percent certainty, the accuracy of the aircraft reported horizontal position. A NACP of 8 or greater is required by § 91.227.
Navigation Integrity Category (NIC)
A parameter that specifies an integrity containment radius. A NIC of 7 or greater is required by § 91.227.
Navigational Accuracy Category for Velocity (NACV)
Used to indicate, with 95 percent certainty, the accuracy of the aircraft reported horizontal velocity. A NACV of 1 or greater is required by § 91.227.
Negative number
A number that is less than zero.
Negative pressure relief valve (pressurization component)
A valve that opens anytime the outside air pressure is greater than the cabin pressure. It prevents the cabin altitude from ever becoming greater than the aircraft flight altitude.
Net thrust
The thrust produced by a turbojet or turbofan engine in which the acceleration factor is the difference between the velocity of the incoming air and the velocity of the exhaust gases leaving the engine.
Neutral axis (neutral plane)
A line through a piece of material that is bent. The material in the outside of the bend is stretched and that on the inside of the bend is shrunk. The material along the neutral plane is neither shrunk nor stretched.
Neutral flame
An oxyacetylene flame produced when the ratio of oxygen and acetylene is chemically correct and there is no excess of oxygen or carbon. A neutral flame has a rounded inner cone and no feather around it.
Neutral position
The position of the magnet in a magneto when its poles are between the pole shoes and no lines of flux are flowing through the magnetic circuit.
Newton
The unit of force needed to accelerate a mass of one kilogram one meter per second per second. One newton is equal to 1000,000 dynes, or 2.248 × 10-1 pound.
Nichrome
The registered trade name for an alloy of nickel and chromium. Nichrome wire is used for making electrical heater elements and precision wire-wound resistors. Nichrome’s resistance is approximately 65 times that of copper.
Nick
A sharp notch-like displacement of metal surface.
Nick
A sharp notch-like displacement of metal usually found on leading and trailing edges.
Nitriding
A method of case hardening steel. Steel is placed in a retort (a sealed, high-temperature furnace and heated to a specified temperature while surrounded by ammonia gas (NH3). The ammonia breaks down into nitrogen and hydrogen, and the nitrogen unites with some of the alloying elements in the steel to form an extremely hard surface. Nitriding hardens crankshaft bearing surfaces and cylinder walls in reciprocating engines. It takes place at a lower temperature than other forms of case hardening, and does not cause warping.
Noise (electrical)
An unwanted electrical signal within a piece of electronic equipment.
Nomex
A patented nylon material used to make the honeycomb core for certain types of sandwich materials.
Nomex braid
Nomex® is the trade name for a high-temperature polyamide thread that is braided over the larger sizes (# 8 gage and larger) of many of the military specification wires. It can be encountered in either an off-white or black/green color.
Nominal Loaded Radius
The allowable tolerance on the loaded radius, and the actual load radius for the test tires should be identified.
Nomogram
A graph that usually consists of three sets of data. Knowledge of any two sets of data enables the reader to determine the third set.
Nonenergizing brake
A brake that does not use the momentum of the aircraft to increase the friction.
Nonvolatile memory
Memory in a computer that is not lost when power to the computer is lost.
Normal category airplane
An aircraft that is certificated under 14 CFR part 23 that is not certificated under the acrobatic, utility, or commuter category.
Normal heptane
A hydrocarbon, C7H16, with a very low critical pressure and temperature. Normal heptane is used as the low reference in measuring the anti-detonation characteristics of a fuel.
Normal shock wave
A type of pressure wave that forms at right angles to a surface when air moves at the speed of sound.
Normal shock wave
A shock wave that forms ahead of a blunt object moving through the air at the speed of sound. The shock wave is normal (perpendicular) to the air approaching the object. Air passing through a normal shock wave is slowed to a subsonic speed and its static pressure is increased.
Normalizing
Reforming of the grain structure of a metal or alloy by proper heat treatment to relieve internal stresses.
Normalizing
The process of heating the part to the proper temperature, holding it at that temperature until it is uniformly heated, and then cooling it in still air.
Normalizing
Aprocess of strain-relieving steel that has been welded and left in a strained condition. The steel is heated to a specified temperature, usually red hot, and allowed to cool in still air to room temperature.
Nose-gear centering cam
A cam in the nose-gear shock strut that causes the piston to center when the strut fully extends. When the aircraft takes off and the strut extends, the wheel is straightened in its fore-and-aft position so it can be retracted into the wheel well.
Notch sensitivity
A measure of the loss of strength of a material caused by the presence of a notch, or a V-shaped cut.
Nozzle guide vanes
See turbine inlet guide vanes.
Nuclear energy
Energy stored in the nucleus of atoms is released during the process of nuclear fission in a nuclear reactor or atomic explosion.
Null position
The position of an ADF loop antenna when the signal being received is canceled in the two sides of the loop and the signal strength is the weakest.
Numerator
The upper part of a fraction (represented by the letter N in N⁄D)
Restrict the list to specific publications by clicking on the menubar at the top of the screen.